NCERT Solutions Class 10 Science Chapter 13 Magnetic Effects of Electric Current

Question

Our NCERT Solutions Class 10 Science Chapter 13 Magnetic Effects of Electric Current is the one-stop solution for all your NCERT solution for preparation for your board exams. These solutions are based on the latest syllabus approved by the CBSE. If you are looking for NCERT solutions then this is just for you. Our NCERT solutions are made by subject matter experts who have a deep understanding of all concepts in this field. We have utilized all kinds of innovative methods such as flow charts, diagrams, shortcuts, tips, and tricks to make the solutions comprehensible and intuitive for the students.

In this NCERT Solutions Class 10 Science Chapter 13 Magnetic Effects of Electric Current we have addressed all kinds of queries of the students with in-depth analysis to make every concept clear and easy to understand for students. In this chapter we have discussed and provided solutions to all topics such as the Basics of magnetism, what is bar magnet, the properties of bar magnets, magnetic field lines and their properties, magnetic field lines and electric current, magnetic field due to a straight current-carrying conductor, right-hand thumb rule, Maxwell’s corkscrew rule, magnetic field due to a current through a circular loop, magnetic field due to a current in a solenoid, the force due to magnetic field lines, using Fleming’s left-hand rule, electric motor (diagram, principle, working), what is electromagnetic induction, how to use Fleming’s Right-hand rule, direct current, alternating current, Electric generator, domestic electric circuit, Natural and artificial magnet, temporary and permanent magnet, live wire, a neutral wire, earth wire, fuse wire, magnetism in human beings, short circuit and overloading, electric motor and electric generator?

Our NCERT Solutions Class 10 Science Chapter 13 Magnetic Effects of Electric Current will help students comprehend the concepts with ease. Our NCERT solution is best for last-minute preparation for their examination. To score good marks one must completely go through all the solutions provided here.

All the solutions are at your fingertip, get started now.

Answer 1

NCERT Solutions Class 10 Science Chapter 13 Magnetic Effects of Electric Current

1. Which of the following correctly describes the magnetic field near a long straight wire? 

(a) The field consists of straight lines perpendicular to the wire. 

(b) The field consists of straight lines parallel to the wire. 

(c) The field consists of radial lines originating from the wire. 

(d) The field consists of concentric circles centred on the wire. 

Answer : 

(d) The field consists of concentric circles centred on the wire. 

On applying right-hand thumb rule, we find the direction of magnetic field. The field is in the form of concentric circles centred on the wire carrying current. 

2. The phenomenon of electromagnetic induction is 

(a) the process of charging a body. 

(b) the process of generating magnetic field due to a current passing through a coil. 

(c) producing induced current in a coil due to relative motion between a magnet and the coil. 

(d) the process of rotating a coil of an electric motor. 

Answer : 

(c) producing induced current in a coil due to relative motion between a magnet and the coil. 

In electromagnetic induction phenomenon an induced current begins to flow in a coil whenever there is change in magnetic field in and around a coil.

3. The device used for producing electric current is called a 

(a) generator. 

(b) galvanometer. 

(c) ammeter. 

(d) motor 

Answer : 

(a) generator. 

An A.C. generator is the device used for producing an electric current.

4. The essential difference between an AC generator and a DC generator is that 

(a) AC generator has an electromagnet while a DC generator has permanent magnet. 

(b) DC generator will generate a higher voltage. 

(c) AC generator will generate a higher voltage. 

(d) AC generator has slip rings while the DC generator has a commutator

Answer : 

(d) AC generator has slip rings while the DC generator has a commutator

5. At the time of short circuit, the current in the circuit 

(a) reduces substantially. 

(b) does not change. 

(c) increases heavily. 

(d) vary continuously. 

Answer : 

(c) increases heavily. 

At the time of short circuiting the live wire and the neutral wire come into direct contact. As a result, the current in the circuit abruptly increases.

6. List three sources of magnetic fields. 

Answer : 

Three methods of producing magnetic field are as follows: 

• Magnetic field can be produced by placing a permanent bar magnet or a horse-shoe magnet at the place, where magnetic field is required. 
• Magnetic field is produced around a current-carrying straight conductor or a current carrying circular coil. 
• A very good method to produce magnetic field is due to flow of current in a solenoid.

7. How does a solenoid behave like a magnet? Can you determine the north and south poles of a current–carrying solenoid with the help of a bar magnet? Explain.

Answer :

When current is passed through a solenoid coil, magnetic field produced due to each turn of solenoid coil is in the same direction. As a resu1t, the resultant magnetic field become very strong and uniform. The field lines inside the solenoid are in the form of parallel straight lines along the axis of solenoid. Thus, the solenoid behaves like a bar magnet. One end of solenoid behaves as a magnetic North pole while the other end behaves as the South Pole.

We can determine the magnetic poles formed in a solenoid. The end of the current-carrying solenoid, which attracts North Pole but repels South Pole of a bar magnet, is behaving as south magnetic pole. The other end, which attracts South Pole of a bar magnet but repels the North Pole, is behaving as north magnetic pole. It is because like poles repel but unlike poles attract each other.

8. When is the force experienced by a current–carrying conductor placed in a magnetic field largest? 

Answer : 

The force experienced by a current-carrying conductor placed in a magnetic field is largest when the current-carrying conductor is placed in a direction perpendicular to that of magnetic field.

9. Imagine that you are sitting in a chamber with your back to one wall. An electron beam, moving horizontally from back wall towards the front wall, is deflected by a strong magnetic field to your right side. What is the direction of magnetic field?

Answer :

An electron beam moving horizontally from back wall towards the front wail is equivalent to a current flowing in the opposite direction (i.e., from front wall towards the back wall). The deflection of electron beam as seen by observer is to his right side and is shown in Figure. On applying Fleming's left-hand rule we find that the magnetic field is acting in vertically downward direction.

10. Name some devices in which electric motors are used. 

Answer : 

Electric motors are used in all such devices where we want to convert electrical energy into mechanical energy so as to drive that machine. In our houses, electric motors are being fitted in electric fans, coolers, air conditioners, mixer grinders, washing machines, refrigerators, juicers, computers etc. In factories, motors are used in almost all machines.

11. A coil of insulated copper wire is connected to a galvanometer. What will happen if a bar magnet is (i) pushed into the coil, (ii) withdrawn from inside the coil, (iii) held stationary inside the coil? 

Answer : 

A current induces in a solenoid if a bar magnet is moved relative to it. This is the principle of electromagnetic induction. 

(i) When a bar magnet is pushed into a coil of insulated copper wire, a current is induced momentarily in the coil. As a result, the needle of the galvanometer deflects momentarily in a particular direction. 

(ii) When the bar magnet is withdrawn from inside the coil of the insulated copper wire, a current is again induced momentarily in the coil in the opposite direction. As a result, the needle of the galvanometer deflects momentarily in the opposite direction. 

(iii) When a bar magnet is held stationary inside the coil, no current will be induced in the coil. Hence, galvanometer will show no deflection.

12. Two circular coils A and B are placed closed to each other. If the current in the coil A is changed, will some current be induced in the coil B? Give reason. 

Answer : 

Yes, a current is induced in the coil B. When the current in the coil A is changed, the magnetic field associated with it also changes. As coil B is placed close to A, hence magnetic field lines around this coil also change. Due to change in magnetic field lines associated with coil B, an induced current is also induced in it.

13. State the rule to determine the direction of a (i) magnetic field produced around a straight conductor-carrying current, (ii) force experienced by a current-carrying straight conductor placed in a magnetic field which is perpendicular to it, and (iii) current induced in a coil due to its rotation in a magnetic field.

Answer :

(i) Maxwell’s right hand thumb rule 

(ii) Fleming’s left hand rule 

(iii) Fleming’s right hand rule

Answer 2

14. When does an electric short circuit occur? 

Answer : 

If either the insulation of wires used in an electrical circuit is damaged or there is a fault in the appliance, live wire and neutral wire may come in direct contact. As a result, the current in the circuit abruptly rises and short-circuiting occurs.

15. What is the function of an earth wire? Why is it necessary to earth metallic appliances? 

Answer : 

The metallic body of electric appliances is connected to the earth by means of earth wire so that any leakage of electric current is transferred to the ground. This prevents any electric shock to the user. That is why earthing of the electrical appliances is necessary.

16. Why does a compass needle get deflected when brought near a bar magnet? 

Answer : 

Magnetic compass needle and bar magnet both have magnetic field. When they brought near to each other, these magnetic fields interact each other giving deflection in needle.

17. Draw magnetic field lines around a bar magnet.

Answer :

18. List the properties of magnetic lines of force. 

Answer : 

Properties of magnetic lines of force (also known as magnetic field lines) are listed below: 

• Outside the magnet, the magnetic field lines are directed from N-pole of magnet towards S-pole. However, inside a magnet the field lines are directed from S-pole to N-pole. Thus magnetic field lines form a close loop. 
• The magnetic field line at any point points in the direction of magnetic field at that point. 
• The relative strength of magnetic fields is given by degree of closeness of the field lines. The magnetic field is strong in the region where the field lines are crowded. 
• No two magnetic field lines can ever intersect with each other.

19. Why don’t two magnetic lines of force intersect each other? 

Answer : 

No two field-lines are found to cross each other. If they did, it would mean that at the point of intersection, the compass needle would point towards two directions, which is not possible.

20. Consider a circular loop of wire lying in the plane of the table. Let the current pass through the loop clockwise. Apply the right-hand rule to find out the direction of the magnetic field inside and outside the loop. 

Answer : 

The magnetic field lines have been shown in Figure given below. As per righthand rule, we find that inside the loop, the magnetic field lines are directed perpendicular to the plane of paper in the inward direction. Outside the loop magnetic field lines are directed out of the plane of paper.

21. The magnetic field in a given region is uniform. Draw a diagram to represent it.

Answer : 

The uniform magnetic field is represented by parallel, equidistant lines of equal length as shown in Figure.

22.  Choose the correct option. 

The magnetic field inside a long straight solenoid-carrying current 

(a) is zero. 

(b) decreases as we move towards its end. 

(c) increases as we move towards its end. 

(d) is the same at all points.

Answer : 

(d) is the same at all points.

23. Which of the following property of a proton can change while it moves freely in a magnetic field? (There may be more than one correct answer.) 

(a) Mass 

(b) Speed 

(c) Velocity 

(d) Momentum

Answer : 

(c) Velocity and (d) Momentum

24. In Activity 13.7, how do we think the displacement of rod AB will be affected if (i) current in rod AB is increased; (ii) a stronger horse-shoe magnet is used; and (iii) length of the rod AB is increased? 

Answer : 

(i) If current in rod AB is increased, the displacement will also increase. 

(ii) If we use a stronger horse-shoe magnet then the displacement of rod AB will increase. 

(iii) lf length of the rod is increased, force acting on it will increase and, hence, displacement of the rod increases.

25. A positively-charged particle (alpha-particle) projected towards west is deflected towards north by a magnetic field. The direction of magnetic field is 

(a) towards south 

(b) towards east 

(c) downward 

(d) upward

Answer : 

(d) upward 

In accordance with Fleming's left-hand rule, the direction of magnetic field is vertically upward.

Answer 3

26. State Fleming’s left-hand rule. 

Answer : 

According to Fleming’s left-hand rule, stretch the thumb, forefinger and middle finger of your left hand such that they are mutually perpendicular. If the first finger points in the direction of magnetic field and the second finger in the direction of current, then the thumb will point in the direction of motion or the force acting on the conductor.

27. What is the principle of an electric motor? 

Answer : 

The working principle of an electric motor is based on the magnetic effect of current. A current-carrying loop experiences a force and rotates when placed in a magnetic field. The direction of rotation of the loop is given by the Fleming’s left-hand rule.

28. What is the role of the split ring in an electric motor?

Answer : 

The split ring in the electric motor acts as a commutator. The commutator reverses the direction of current flowing through the coil after each half rotation of the coil. Due to this reversal of the current, the coil continues to rotate in the same direction.

29. Explain different ways to induce current in a coil.

Different ways to induce current in a coil are as given below: 

• If a magnetic field is changed around a coil then an induced current is set up in the coil. It can be done by taking a bar magnet and bringing it closer to the coil or taking it away from the coil. 
• If a coil is moved in a magnetic field, then again an induced current is set up in the coil. 
• If a coil is rotated in a uniform magnetic field, it may also produce an induced current in the coil.

30. State the principle of an electric generator. 

Answer : 

An electric generator is based on the principle of electromagnetic induction. When a rectangular coil is rotated in a uniform magnetic field, an induced voltage is generated between the ends of the coil.

31. Name some sources of direct current. 

Answer : 

Some sources of direct current are a cell, a battery and a D.C. generator.

32. Which sources produce alternating current? 

Answer :

A.C. generator and invertors (used in house for emergency power supply) produces alternating current.

33. Choose the correct option. 

A rectangular coil of copper wires is rotated in a magnetic field. The direction of the induced current changes once in each 

(a) two revolutions 

(b) one revolution 

(c) half revolution 

(d) one-fourth revolution

Answer : 

(c). When a rectangular coil of copper wire is rotated in a magnetic field, the direction of the induced current changes once in each half revolution.

34. Name two safety measures commonly used in electric circuits and appliances. 

Answer : 

Two safety measures are: 

Use of earth wire and proper earthing. 

Use of fuse (now a days fuse wire is replaced by MCB).

35. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. 

Answer : 

Power rating of electric oven P = 2 kW = 2000 W 

Supply voltage V = 220 V

So, the current drawn by electric oven = \(\frac{P}{V}\)= \(\frac{2000\,W}{220\,V}\) = 9A

36. What precaution should be taken to avoid the overloading of domestic electric circuits? 

Answer : 

The precautions that should be taken to avoid the overloading of domestic circuits are as follows: 

Too many appliances should not be connected to a single socket. 

Too many appliances should not be used at the same time. 

Faulty appliances should not be connected in the circuit. 

Fuse should be connected in the circuit.